Filter

I want to watch

  • Garage freeze probe

    Verified on hardware

    Hardware:
    ESP32 dev board + DS18B20 waterproof probe + 4.7 kΩ resistor
    Setup:
    Web flasher (no code)
    Watches:
    Freeze / temperature

    Data to GPIO 4, resistor from data to 3.3 V. Clip the probe to the pipe, not the air. Several probes can share the wire.

    Web flasherESP32 freeze kit

  • Temperature + humidity

    Verified on hardware

    Hardware:
    ESP32 dev board + DHT22 (AM2302) module
    Setup:
    Web flasher (no code)
    Watches:
    Freeze / temperature, Humidity

    Same GPIO 4 as the DS18B20. Mount it away from the board; the ESP32 warms a sensor sitting next to it. A DHT11 is detected too, but isn't hardware-tested and reads coarser.

    Web flasherDHT22 wiring

  • Temperature, humidity + pressure

    Verified on hardware

    Hardware:
    ESP32 dev board + BME280 on I²C
    Setup:
    Web flasher (no code)
    Watches:
    Freeze / temperature, Humidity, Air quality / pressure

    Found automatically at boot: SDA to GPIO 21, SCL to GPIO 22, plus 3.3 V and GND. Reports air pressure as well. A BMP280 looks the same but has no humidity, so check the listing.

    Web flasher

  • Temperature + humidity on I²C

    Verified on hardware

    Hardware:
    ESP32 dev board + SHT31 on I²C
    Setup:
    Web flasher (no code)
    Watches:
    Freeze / temperature, Humidity

    Found automatically at boot: SDA to GPIO 21, SCL to GPIO 22, plus 3.3 V and GND. Temperature and humidity only, no pressure.

    Web flasher

  • Other I²C air sensors

    Verified on hardware

    Hardware:
    ESP32 + AHT20 on I²C
    Setup:
    Web flasher (no code)
    Watches:
    Freeze / temperature, Humidity

    Found automatically at boot. Run on an ESP32-S3 (SDA 8, SCL 9) and on a classic ESP32, wired like the BME280 and SHT31 (SDA 21, SCL 22).

    Web flasher

  • Door contact

    Verified on hardware

    Hardware:
    ESP32 dev board + magnetic reed switch
    Setup:
    Web flasher, extras option
    Watches:
    Door

    Tick Door in the flasher's extras. On a classic ESP32 the reed switch goes from GPIO 26 to GND; magnet away reads Open. Mount the magnet on the door and the switch on the frame.

    Web flasher

  • Leak contact

    Built in, not yet hardware-tested

    Hardware:
    ESP32 + an LM393 water sensor module or two bare wires
    Setup:
    Web flasher, extras option
    Watches:
    Leak

    Tick Leak in the flasher's extras. On a classic ESP32 the contact goes from GPIO 27 to GND. A wet contact raises a leak alert with no other setup.

    Web flasher

  • Battery-powered probe

    Built in, not yet hardware-tested

    Hardware:
    ESP32 with a LiPo through a 1:1 voltage divider (GPIO 35 on a classic ESP32)
    Setup:
    Web flasher, extras option
    Watches:
    Battery

    Reports battery percentage so Devices can warn before it dies. Expect weeks, not months, on Wi-Fi.

    Web flasher

  • ESP32-S3 boards

    Verified on hardware

    Hardware:
    ESP32-S3 dev board
    Setup:
    Web flasher (no code)
    Watches:
    Freeze / temperature, Humidity

    Run on hardware with an AHT20 on SDA 8, SCL 9. Settings go over either USB port (firmware 1.2.4 or later). A DS18B20 or DHT22 goes on GPIO 4, as on a classic ESP32.

    Web flasher

  • ESP32-C3 boards

    Verified on hardware

    Hardware:
    ESP32-C3 dev board
    Setup:
    Web flasher (no code)
    Watches:
    Freeze / temperature, Humidity

    Run on hardware with a DHT22 on GPIO 4. Settings go over either USB port (firmware 1.2.5 or later).

    Web flasher

  • Sensors already in Home Assistant

    Guide: you write the code

    Hardware:
    Any Zigbee, Z-Wave, or Wi-Fi sensor Home Assistant can see
    Setup:
    HACS integration
    Watches:
    Freeze / temperature, Humidity, Leak, Door

    An automation pushes entity states to ProbeHarbor, so alerts still reach you when Home Assistant or the power is down. Needs a little YAML.

    Home AssistantNotify recipes

  • ESPHome or Shelly devices

    Guide: you write the code

    Hardware:
    ESPHome firmware, or a Shelly H&T / Flood
    Setup:
    http_request / webhook
    Watches:
    Freeze / temperature, Humidity, Leak

    Point the device's HTTP action at your ingest URL. Copy the ESPHome snippet from your device's page.

    ESPHome & Shelly recipesPayload checker

  • An MQTT feed

    Guide: you write the code

    Hardware:
    Anything already publishing to an MQTT broker
    Setup:
    MQTT bridge or Node-RED
    Watches:
    Freeze / temperature, Humidity, Leak, Door, Air quality / pressure

    Forward topics to the ingest endpoint. Check one message with the payload checker before wiring the flow.

    MQTT bridgeNode-REDPayload checker

  • Arduino sketches

    Guide: you write the code

    Hardware:
    Arduino with Ethernet/Wi-Fi, ESP8266, or ESP32 in the Arduino IDE
    Setup:
    Arduino sketch posting JSON
    Watches:
    Freeze / temperature, Humidity

    Start from an example sketch and change the key and pins.

    Arduino sketchesPayload checker

  • Raspberry Pi Pico W

    Guide: you write the code

    Hardware:
    Pico W + DS18B20 or DHT22, MicroPython
    Setup:
    MicroPython script
    Watches:
    Freeze / temperature, Humidity

    A short script reads the sensor and posts JSON over Wi-Fi.

    Pico W guidePayload checker

  • Your own HTTPS JSON feed

    Guide: you write the code

    Hardware:
    A server, script, or device that already serves readings as JSON
    Setup:
    Pull feed (we poll it)
    Watches:
    Freeze / temperature, Humidity

    Add the URL under Devices → Pull feeds; we fetch it on a schedule.

    Python feedsAdding devices

  • No Wi-Fi at the site

    Guide: you write the code

    Hardware:
    Cellular modem board (e.g. SIM7000 / LTE-M)
    Setup:
    Cellular POST
    Watches:
    Freeze / temperature

    For cabins and outbuildings without Wi-Fi. Data plans and power are the hard parts.

    Cellular ingestPayload checker

What the labels mean

  • Verified on hardware: we've run this combination on a real board and seen readings arrive.
  • Built in, not yet hardware-tested: the flasher firmware supports it, but we haven't wired one up ourselves yet. Tell us if it works for you.
  • Guide: you write the code: a documented path where you adapt example code or configuration. Anything that can send JSON over HTTPS can report.